Independent buying guides for leathercraft

How to Punch Holes in Leather Cleanly With or Without a Special Punch

Published How we research

A neat round hole is the difference between a strap that looks professional and one that looks like a mistake. Holes for belts, buckles, snaps, rivets and lacing all need the right size, the right spacing and a clean cut, and a dull or badly chosen tool tears the leather or leaves a ragged oval. The good news is that the job is simple once you know the options. This guide covers the main kinds of punch, how to pick a size, how to mark positions, how to strike or squeeze for a clean cut, and what to do when you have no proper tool, including safety notes for working with sharp tools.

Products from this article

The highest-scoring picks from the buying guides this article links to. Scores are our editorial assessment, not customer ratings.

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Choose the right type of punch

A rotary punch has a wheel of different sizes and is operated with a hand squeeze, which makes it a good choice for thinner leather and a quick, accurate cut. A drive punch, struck with a mallet, cuts a single size and handles thicker leather very well.

Oval and slot punches suit belts and strap adjustment holes, while a thin awl is made for stitching holes, not for large openings. Many makers own a rotary punch for everyday jobs and a small set of drive punches for heavier work.

Pick the right hole size

Check the size recommended for your hardware. Snaps, rivets and buckle tongues all have a stated stem or tongue width, and the hole should be just large enough for that part to pass through without slop. Use the hardware maker's guidance.

If a hole is too small the leather may bulge or tear when you force the part through, and if it is too large the fastener will wobble or pull out. Test on a scrap of the same leather before you cut the real piece.

Mark the positions accurately

Mark with a scratch awl or a pencil, and use a ruler or dividers for even spacing. For belts, many people mark a row of evenly spaced holes along the centerline, then check the spacing against the buckle before punching.

Keep holes far enough from the edge so the leather does not tear. A common rule of thumb is to stay back at least a few times the hole width, but check the project requirements, and give thinner or softer leather more margin.

Use the right backing surface

Place the leather on a poundo board, a piece of scrap leather or a self-healing surface, never on hard stone or metal, which will dull and damage the punch. A firm, slightly giving backing lets the cutting edge go through cleanly.

Work on a stable bench at a height where you can strike straight down. A wobbling table makes holes uneven and makes the tool more likely to slip, which is a safety concern as well as a quality one.

How to strike or squeeze for a clean cut

With a drive punch, hold it vertical with the cutting edge on your mark and strike with a mallet in one or two firm blows. Twist the punch slightly to release the plug, and check that the hole is clean through.

With a rotary punch, align the tube over the mark and squeeze firmly in one smooth motion. If the cut is not clean on the first squeeze, the tube may be dull or the leather too thick, so switch to a drive punch rather than forcing it.

Holes for stitching are different

Stitch holes are small and are typically made with an awl, pricking irons or stitching chisels rather than round punches. Chisels leave slits that close up a bit and give a neat, slanted stitch, while an awl makes a single hole at a time.

Our guide on stitching chisel and pricking iron sizes explains how to match spacing to thread, and the saddle stitch article shows how the holes fit into the stitch.

→

Fixing common problems

Ragged or torn holes usually mean a dull punch, thin or dry leather, or too little backing. Sharpen or replace the punch, case the leather lightly if the type allows, and use a firmer backing surface.

Oval holes come from a punch that was tilted or struck off-vertical. Slow down, hold the tool straight, and check the angle from two sides before striking. If a hole is wrong, you may be able to cover it with a rivet, snap or decorative piece.

Punching without a proper tool

If you have no punch, a sharp awl can make small holes, and a drill with a sharp bit may work on firm leather clamped over scrap wood. Results are rougher than a punch, so keep this for rough use or emergency fixes.

Wear eye protection when using a drill, clamp the work, and keep fingers away from the bit. Whichever method you use, keep tools sharp, cut away from your body and store blades and punches safely when you finish.

Safety and tool care

Punches and knives are sharp, and a mallet can slip, so keep your free hand away from the strike zone and never hold the leather over a punch with your fingers underneath. Wear eye protection if you strike hard or work with brittle leather.

Keep cutting edges sharp, since dull tools need more force and slip more often. Wipe them dry after use, store them with their edges protected, and replace tubes that have chipped, because a damaged edge leaves ragged holes however carefully you work.

Spacing for belts and straps

For a belt, holes are usually spaced evenly along the strap so the wearer can adjust the fit, and many makers check the spacing against an existing belt they like. Keep the row centered and parallel to the edges so the buckle sits straight.

Make a paper or card template with the hole positions marked, and reuse it for later belts. A template speeds up marking and keeps the holes consistent, which is especially helpful if you make several belts in different sizes.

Popular right now

  1. Setting Rivets and SnapsArticle
  2. Best Pricking Irons for Clean, Slanted Saddle StitchesBuying guide
  3. Best Gum Tragacanth and Burnishing Agents for Leather EdgesBuying guide
  4. How to Dye Leather EvenlyArticle
  5. Choosing Your First Leather KnifeArticle
  6. Hand Stitching vs Machine Stitching LeatherArticle

Based on the last 28 days of search and visitor data.